FlashKa Keychain housing v0.7 drawings (2026-10-23): every number written on the sheets against its value in P (574 entries, 441 distinct; 'shown' = value as printed, tolerance 6e-4) == FK-H-01 1/2 sheet what shown P expression P value ok --------------------------------------------------------------------------------------------------------------------------------- FK-H-01 1/2 front taps from the front face 10.14 screw_x_front 10.14 ok [top] FK-H-01 1/2 rear taps from the front taps 85.81 X_screw_back-screw_x_front 85.81 ok [top] FK-H-01 1/2 rear taps from the tail face 3.25 L-X_screw_back 3.25 ok [top] FK-H-01 1/2 head block length 11.45 L_head 11.45 ok [top, secD, table] FK-H-01 1/2 KB bosses from the head block 14.2 kb_holes[0][0]-L_head 14.2 ok [top] FK-H-01 1/2 bosses to the end of the ledges 9.9 X_pcb1-kb_holes[0][0] 9.9 ok [top] FK-H-01 1/2 antenna zone + cell bay 57.8 X_batt1-X_pcb1 57.8 ok [top] FK-H-01 1/2 tail (front wall + slot + end wall) 5.85 L_tail 5.85 ok [top] FK-H-01 1/2 overall length 99.2 L 99.2 ok [top] FK-H-01 1/2 width 20 W 20 ok [top, secB] FK-H-01 1/2 thread depth 2.6 m16_drill-1.0 2.6 ok [top, secC, table] FK-H-01 1/2 tap drill 1.25 m16_tap 1.25 ok [top, secC, table] FK-H-01 1/2 tap drill depth 3.6 m16_drill 3.6 ok [top, secC, table] FK-H-01 1/2 front relief dia 2 front_relief[0] 2 ok [top, table] FK-H-01 1/2 USB-C centre from the front face 17.35 X_usb 17.35 ok [side_m] FK-H-01 1/2 height 18 H 18 ok [side_m, side_p, front] FK-H-01 1/2 USB-C opening width 12.6 usb_open[0] 12.6 ok [side_m, table] FK-H-01 1/2 USB-C opening height 6.8 usb_open[1] 6.8 ok [side_m, table] FK-H-01 1/2 USB-C opening radius 2 usb_open[2] 2 ok [side_m, table] FK-H-01 1/2 USB-C centre Z 7.595 Z_pcb_bot-3.21/2 7.595 ok [side_m, table] FK-H-01 1/2 USB-C chamfer 0.3 usb_open_chamfer 0.3 ok [side_m, table] FK-H-01 1/2 S2 slot centre from the front face 16.8 X_s2 16.8 ok [side_p] FK-H-01 1/2 S2 slot width 3.2 s2_slot[0] 3.2 ok [side_p, table] FK-H-01 1/2 S2 slot height 2 s2_slot[1] 2 ok [side_p, table] FK-H-01 1/2 S2 slot radius 0.8 s2_slot[2] 0.8 ok [side_p, table] FK-H-01 1/2 S2 slot centre Z 10.7 Z_pcb_top+s2_knob_z 10.7 ok [side_p, table] FK-H-01 1/2 optic bore depth 8.83 D_w 8.83 ok [secA, table] FK-H-01 1/2 optic bore diameter 10.1 opt_bore 10.1 ok [secA, front, secE] FK-H-01 1/2 cavity depth (floor to lid seat) 13.1 Z_lid-floor 13.1 ok [secA] FK-H-01 1/2 PCB ledge height 9.2 Z_pcb_bot 9.2 ok [secA, secB] FK-H-01 1/2 laser axis from the +Y face 4.15 W/2-Y_l 4.15 ok [front, table] FK-H-01 1/2 optic axis to laser axis 9.675 Y_l-Y_w 9.675 ok [front] FK-H-01 1/2 optic axis from the control face 6.175 W/2+Y_w 6.175 ok [front, table] FK-H-01 1/2 laser axis height 5.9 Z_las 5.9 ok [front, secD] FK-H-01 1/2 optic axis height 8 Z_axis 8 ok [front] FK-H-01 1/2 laser bore diameter 6.1 las_d+las_clear 6.1 ok [front, secC, secD] FK-H-01 1/2 tap spacing 9 2*screw_dy 9 ok [secC] FK-H-01 1/2 LED wire hole diameter 1.5 ledwire_d 1.5 ok [secC] FK-H-01 1/2 cavity width 17 2*(W/2-wall) 17 ok [secB, table] FK-H-01 1/2 main key opening (Y) 7 main_key[1]+2*key_clear 7 ok [secB] FK-H-01 1/2 KB boss top 4.4 kb_z0 4.4 ok [secB] FK-H-01 1/2 lid seat height 14.6 Z_lid 14.6 ok [secB] FK-H-01 1/2 KB tap thread length 1.85 kb_z0-kb_thread_z 1.85 ok [secB] FK-H-01 1/2 KB tap drill 1.25 m16_tap 1.25 ok [secB, table] FK-H-01 1/2 KB tap drill depth 2.375 kb_z0-kb_drill_z 2.375 ok [secB] FK-H-01 1/2 laser set screw from the front face 5.5 las_set[0] 5.5 ok [secD] FK-H-01 1/2 laser set-screw thread length 5.836 Z_lid-las_set_bore_z 5.836 ok [secD, table] FK-H-01 1/2 laser set-screw tap drill 1.25 m16_tap 1.25 ok [secD, table] FK-H-01 1/2 laser set screw length 5 las_set_len 5 ok [secD] FK-H-01 1/2 optic bore dia 10.1 opt_bore 10.1 ok [table] FK-H-01 1/2 optic axis Y -3.825 Y_w -3.825 ok [table] FK-H-01 1/2 optic axis Z 8 Z_axis 8 ok [table] FK-H-01 1/2 LED wire groove angle from vertical 30 led_wire_ang 30 ok [table] FK-H-01 1/2 groove width 1.4 wire_groove[0] 1.4 ok [table] FK-H-01 1/2 groove bottom radius 6.35 opt_bore/2+wire_groove[1] 6.35 ok [table] FK-H-01 1/2 groove start X 6.13 x_led_board-1.0 6.13 ok [table] FK-H-01 1/2 groove end X 8.83 D_w 8.83 ok [table] FK-H-01 1/2 wire hole dia 1.5 ledwire_d 1.5 ok [table] FK-H-01 1/2 wire hole radius from the axis 5.7 led_wire_r 5.7 ok [table] FK-H-01 1/2 upper wire hole Y -0.975 Y_w+led_wire_r*sin(led_wire_ang) -0.975 ok [table] FK-H-01 1/2 upper wire hole Z 12.94 Z_axis+led_wire_r*cos(led_wire_ang), rounded 12.94 ok [table] FK-H-01 1/2 upper wire hole end X 11.46 led_wire_hole_x_end[0], rounded to 2 dec 11.46 ok [table] FK-H-01 1/2 lower wire hole Y -6.675 Y_w-led_wire_r*sin(led_wire_ang) -6.675 ok [table] FK-H-01 1/2 lower wire hole Z 3.06 Z_axis-led_wire_r*cos(led_wire_ang), rounded 3.06 ok [table] FK-H-01 1/2 lower wire hole end X 12.64 led_wire_hole_x_end[1], rounded to 2 dec 12.64 ok [table] FK-H-01 1/2 laser bore dia 6.1 las_d+las_clear 6.1 ok [table] FK-H-01 1/2 laser axis Y 5.85 Y_l 5.85 ok [table] FK-H-01 1/2 laser axis Z 5.9 Z_las 5.9 ok [table] FK-H-01 1/2 laser module diameter 6 las_d 6 ok [table] FK-H-01 1/2 laser module length 12 las_len 12 ok [table] FK-H-01 1/2 laser recess 0.3 las_recess 0.3 ok [table] FK-H-01 1/2 laser set screw X 5.5 las_set[0] 5.5 ok [table] FK-H-01 1/2 laser set screw Y 4.8 las_set[1] 4.8 ok [table] FK-H-01 1/2 front tap X 10.14 screw_x_front 10.14 ok [table] FK-H-01 1/2 rear tap X 95.95 X_screw_back 95.95 ok [table] FK-H-01 1/2 tap Y 4.5 screw_dy 4.5 ok [table] FK-H-01 1/2 ledge height 9.2 Z_pcb_bot 9.2 ok [table] FK-H-01 1/2 ledge width 0.8 ledge_w 0.8 ok [table] FK-H-01 1/2 ledge start X 11.45 L_head 11.45 ok [table] FK-H-01 1/2 ledge end X 35.55 X_pcb1 35.55 ok [table] FK-H-01 1/2 USB-C gap start 12.45 X_usb-4.9 12.45 ok [table] FK-H-01 1/2 USB-C gap end 22.35 X_usb+5.0 22.35 ok [table] FK-H-01 1/2 laser keepout X 15.65 las_keepout_x 15.65 ok [table] FK-H-01 1/2 USB-C X 17.35 X_usb 17.35 ok [table] FK-H-01 1/2 next key X 18.65 X_next 18.65 ok [table] FK-H-01 1/2 main key X 25.65 X_main 25.65 ok [table] FK-H-01 1/2 prev key X 32.65 X_prev 32.65 ok [table] FK-H-01 1/2 key Y 0 key_y 0 ok [table] FK-H-01 1/2 side key opening X 4.4 side_key[0]+2*key_clear 4.4 ok [table] FK-H-01 1/2 side key opening Y 10.3 side_key[1]+2*key_clear_end 10.3 ok [table] FK-H-01 1/2 side key opening radius 1.6 side_key[2]+key_clear 1.6 ok [table] FK-H-01 1/2 main key opening X 7 main_key[0]+2*key_clear 7 ok [table] FK-H-01 1/2 main key opening Y 7 main_key[1]+2*key_clear 7 ok [table] FK-H-01 1/2 main key opening radius 1.1 main_key[2]+key_clear 1.1 ok [table] FK-H-01 1/2 S2 X 16.8 X_s2 16.8 ok [table] FK-H-01 1/2 wall 1.5 wall 1.5 ok [table] FK-H-01 1/2 floor Z 1.5 floor 1.5 ok [table] FK-H-01 1/2 lid seat Z 14.6 Z_lid 14.6 ok [table] FK-H-01 1/2 inner corner radius 2 inner_r 2 ok [table, notes] FK-H-01 1/2 diagonal wall 1.5 wall 1.5 ok [table] FK-H-01 1/2 trough width 15.4 2*(inner_half-ledge_w) 15.4 ok [table] FK-H-01 1/2 rail inner Y 3.5 rail_y 3.5 ok [table] FK-H-01 1/2 rail outer Y 4.7 rail_y+rail_w 4.7 ok [table] FK-H-01 1/2 rail top Z 2.6 floor+rail_h 2.6 ok [table] FK-H-01 1/2 rail start X 44.75 X_batt0+3.0 44.75 ok [table] FK-H-01 1/2 rail end X 90.35 X_batt1-3.0 90.35 ok [table] FK-H-01 1/2 front relief bottom Z 9.2 Z_pcb_bot 9.2 ok [table] FK-H-01 1/2 front relief X 12.35 L_head+front_relief[1] 12.35 ok [table] FK-H-01 1/2 front relief Y 7.9 inner_half-front_relief[2] 7.9 ok [table] FK-H-01 1/2 boss dia 3.4 boss_d 3.4 ok [table] FK-H-01 1/2 boss X 25.65 kb_holes[0][0] 25.65 ok [table] FK-H-01 1/2 boss Y 5.8 kb_holes[0][1] 5.8 ok [table] FK-H-01 1/2 boss top Z 4.4 kb_z0 4.4 ok [table] FK-H-01 1/2 KB drill end Z 2.025 kb_drill_z 2.025 ok [table] FK-H-01 1/2 KB thread end Z 2.55 kb_thread_z 2.55 ok [table] FK-H-01 1/2 KB screw length 2.5 kb_screw_len 2.5 ok [table] FK-H-01 1/2 rib width 1.4 rib_w 1.4 ok [table] FK-H-01 1/2 rib inner Y 5.9 rib_y0 5.9 ok [table] FK-H-01 1/2 rib top Z 4.4 kb_z0 4.4 ok [table] FK-H-01 1/2 free post X 18.65 kb_ribs[0][0] 18.65 ok [table] FK-H-01 1/2 free post inner Y 5.9 rib_y0 5.9 ok [table] FK-H-01 1/2 free post outer Y 7.1 kb_y-0.3 7.1 ok [table] FK-H-01 1/2 optic diameter 10 opt_od 10 ok [notes] FK-H-01 1/2 LED board diameter 10 mcpcb_d 10 ok [notes] FK-H-01 1/2 bore floor X 8.83 D_w 8.83 ok [notes] FK-H-01 1/2 wall optic bore - control face 1.125 min_walls 1.125 ok [notes] FK-H-01 1/2 wall laser bore - +Y face 1.1 min_walls 1.1 ok [notes] FK-H-01 1/2 wall front tap - head back face 0.685 min_walls 0.685 ok [notes] FK-H-01 1/2 wall front tap - bore floor 0.685 min_walls 0.685 ok [notes] FK-H-01 1/2 wall front tap crest - head back face 0.51 min_walls 0.51 ok [notes] FK-H-01 1/2 wall front tap crest - bore floor 0.51 min_walls 0.51 ok [notes] FK-H-01 1/2 wall upper LED wire groove - head-block top 0.751 min_walls 0.751 ok [notes] FK-H-01 1/2 wall tail front 0.8 min_walls 0.8 ok [notes] FK-H-01 1/2 wall floor under the bezel 1 min_walls 1 ok [notes] FK-H-01 1/2 wall floor web 1.3 min_walls 1.3 ok [notes] FK-H-01 1/2 wall under the KB tap 1.649 min_walls 1.649 ok [notes] FK-H-01 1/2 pocket depth 13.1 Z_lid-floor 13.1 ok [notes] FK-H-01 1/2 section A-A plane -3.825 Y_w -3.825 ok [notes] FK-H-01 1/2 section D-D plane 4.8 las_set[1] 4.8 ok [notes] FK-H-01 1/2 section B-B plane 25.65 X_main 25.65 ok [notes] FK-H-01 1/2 section C-C plane 10.14 screw_x_front 10.14 ok [notes] == FK-H-01 2/2 sheet what shown P expression P value ok --------------------------------------------------------------------------------------------------------------------------------- FK-H-01 2/2 next key from the front face 18.65 X_next 18.65 ok [bottom] FK-H-01 2/2 main key from the next key 7 X_main-X_next 7 ok [bottom] FK-H-01 2/2 previous key from the main key 7 X_prev-X_main 7 ok [bottom] FK-H-01 2/2 floor RF window from the previous key 3.7 frw_box[0]-X_prev 3.7 ok [bottom] FK-H-01 2/2 floor RF window length 5.1 frw_box[1]-frw_box[0] 5.1 ok [bottom, table] FK-H-01 2/2 bottom panel 1 length 27.75 panel_layout 27.75 ok [bottom] FK-H-01 2/2 bottom panel 2 length 20.85 panel_layout 20.85 ok [bottom] FK-H-01 2/2 bezel width (at the face) 11.6 bezel 11.6 ok [bottom] FK-H-01 2/2 panel width 10.8 2*(W/2-C_edge-rail) 10.8 ok [bottom] FK-H-01 2/2 tail window width 10.8 twin_y 10.8 ok [bottom, table] FK-H-01 2/2 lanyard slot length 4.6 lan_slot_len 4.6 ok [bottom, table] FK-H-01 2/2 floor RF window width 10.8 2*frw_box[2] 10.8 ok [bottom, table] FK-H-01 2/2 floor RF window radius 1.5 frw_box[3] 1.5 ok [bottom, table] FK-H-01 2/2 side panel bottom Z 4.6 C_edge+rail 4.6 ok [side_m] FK-H-01 2/2 side panel top Z 13.4 Z_lid-rail 13.4 ok [side_m] FK-H-01 2/2 height 18 H 18 ok [side_m, table] FK-H-01 2/2 side PCB-zone panel start 25.15 panel_layout 25.15 ok [side_m] FK-H-01 2/2 side PCB-zone panel length 16.9 panel_layout 16.9 ok [side_m] FK-H-01 2/2 side bay panel length 20.85 panel_layout 20.85 ok [side_m] FK-H-01 2/2 band between the bay panels 1.2 band 1.2 ok [side_m] FK-H-01 2/2 +Y PCB-zone panel start 19.6 panel_layout 19.6 ok [side_m] FK-H-01 2/2 bezel depth 0.5 bez_depth 0.5 ok [secK, table] FK-H-01 2/2 floor 1.5 floor 1.5 ok [secK] FK-H-01 2/2 bezel length (at the face) 19.8 bezel 19.8 ok [secK] FK-H-01 2/2 texture groove width 0.4 2*tex_depth 0.4 ok [secV, table] FK-H-01 2/2 texture pitch 0.9 tex_pitch 0.9 ok [secV, table] FK-H-01 2/2 texture groove depth 0.2 tex_depth 0.2 ok [secV] FK-H-01 2/2 transverse groove width 0.6 2*grv_depth 0.6 ok [secG] FK-H-01 2/2 transverse groove depth 0.3 grv_depth 0.3 ok [secG, table] FK-H-01 2/2 width 20 W 20 ok [table] FK-H-01 2/2 facet leg 3.4 C_edge 3.4 ok [table] FK-H-01 2/2 bottom facet width 13.2 W-2*C_edge 13.2 ok [table] FK-H-01 2/2 side facet height 11.2 H-2*C_edge 11.2 ok [table] FK-H-01 2/2 diagonal facet width 4.81 C_edge*sqrt2, rounded to 2 dec 4.81 ok [table] FK-H-01 2/2 front outline chamfer 0.4 C_front 0.4 ok [table] FK-H-01 2/2 tail outline chamfer 0.6 C_end 0.6 ok [table] FK-H-01 2/2 lid seat Z 14.6 Z_lid 14.6 ok [table] FK-H-01 2/2 panel depth 0.3 pan_depth 0.3 ok [table] FK-H-01 2/2 panel corner radius 0.8 pan_r 0.8 ok [table] FK-H-01 2/2 frame band 1.2 band 1.2 ok [table] FK-H-01 2/2 rail 1.2 rail 1.2 ok [table] FK-H-01 2/2 texture depth 0.2 tex_depth 0.2 ok [table] FK-H-01 2/2 texture grid step 1.273 tex_pitch*sqrt2 1.273 ok [table] FK-H-01 2/2 texture land 0.5 tex_pitch-2*tex_depth 0.5 ok [table] FK-H-01 2/2 bezel floor margin 0.3 bez_margin 0.3 ok [table] FK-H-01 2/2 bezel start X 15.75 X_next-side_key[0]/2-bez_margin-bez_depth 15.75 ok [table] FK-H-01 2/2 bezel end X 35.55 X_prev+side_key[0]/2+bez_margin+bez_depth 35.55 ok [table] FK-H-01 2/2 bezel half width 5.8 side_key[1]/2+bez_margin+bez_depth 5.8 ok [table] FK-H-01 2/2 floor RF window start X 36.35 frw_box[0] 36.35 ok [table] FK-H-01 2/2 floor RF window end X 41.45 frw_box[1] 41.45 ok [table] FK-H-01 2/2 tail window length 4.1 twin_x 4.1 ok [table] FK-H-01 2/2 tail window depth 1 twin_depth 1 ok [table] FK-H-01 2/2 tail window corner 0.8 twin_r 0.8 ok [table] FK-H-01 2/2 tail window big corner 1.8 twin_corner 1.8 ok [table] FK-H-01 2/2 tail window chamfer 0.3 twin_chamfer 0.3 ok [table] FK-H-01 2/2 tail window start X 94.15 max(X_lan-twin_x/2,X_batt1+twin_front_gap) 94.15 ok [table] FK-H-01 2/2 tail window end X 98.25 X_lan+twin_x/2 98.25 ok [table] FK-H-01 2/2 lanyard slot width 3.6 lan_slot_w 3.6 ok [table] FK-H-01 2/2 lanyard slot centre X 95.95 X_lan 95.95 ok [table] FK-H-01 2/2 lanyard slot chamfer 0.25 lan_chamfer 0.25 ok [table] FK-H-01 2/2 tail facet 2 tail_facet 2 ok [table] FK-H-01 2/2 min metal under texture or grooves 1 texture_min_metal_mm 1 ok [notes] FK-H-01 2/2 main key face below the bottom plane 0.15 main_face_z 0.15 ok [notes] FK-H-01 2/2 side key face below the bottom plane 0.3 side_face_z 0.3 ok [notes] FK-H-01 2/2 chevron top below the bottom plane 0.1 side_face_z-chevron_h 0.1 ok [notes] == FK-H-02 1/1 sheet what shown P expression P value ok --------------------------------------------------------------------------------------------------------------------------------- FK-H-02 1/1 front screws from the lid front edge 5.94 screw_x_front-lid_x0 5.94 ok [top] FK-H-02 1/1 screw spacing along X 85.81 X_screw_back-screw_x_front 85.81 ok [top] FK-H-02 1/1 rear screws to the lid end 3.25 L-X_screw_back 3.25 ok [top] FK-H-02 1/1 first panel from the lid front edge 8.79 panel_layout 8.79 ok [top] FK-H-02 1/1 PCB-zone panel length 19.76 panel_layout 19.76 ok [top] FK-H-02 1/1 RF opening length 6.9 rfw_box[1]-rfw_box[0] 6.9 ok [top, under, table] FK-H-02 1/1 bay panel 1 length 20.85 panel_layout 20.85 ok [top] FK-H-02 1/1 bay panel 2 length 20.85 panel_layout 20.85 ok [top] FK-H-02 1/1 lid length 95 L-lid_x0 95 ok [top] FK-H-02 1/1 screw spacing across 9 2*screw_dy 9 ok [top] FK-H-02 1/1 RF opening width 10.8 rfw_y 10.8 ok [top, under, table] FK-H-02 1/1 panel width 10.8 2*(W/2-C_edge-rail) 10.8 ok [top] FK-H-02 1/1 lanyard slot length 4.6 lan_slot_len 4.6 ok [top, table] FK-H-02 1/1 tail end width 16 W-2*tail_facet 16 ok [top] FK-H-02 1/1 RF pocket length 8.5 rfw_box[1]-rfw_box[0]+2*rfw_flange 8.5 ok [under, table] FK-H-02 1/1 hold-down boss length 8.8 boss_box[1]-boss_box[0] 8.8 ok [under] FK-H-02 1/1 hold-down boss width 12.4 boss_box[3]-boss_box[2] 12.4 ok [under] FK-H-02 1/1 front boss length 3.7 boss2_box[1]-boss2_box[0] 3.7 ok [under, secG] FK-H-02 1/1 front boss width 3 boss2_box[3]-boss2_box[2] 3 ok [under] FK-H-02 1/1 flat top width 13.2 W-2*C_edge 13.2 ok [secJ, table] FK-H-02 1/1 lid height (seat to top) 3.4 H-Z_lid 3.4 ok [secJ] FK-H-02 1/1 facet leg 3.4 C_edge 3.4 ok [secJ, table] FK-H-02 1/1 can boss length 8.8 boss_box[1]-boss_box[0] 8.8 ok [secG] FK-H-02 1/1 can boss height 2.95 Z_ceil-can_top_z-pad_gap 2.95 ok [secG] FK-H-02 1/1 front boss height 5.75 Z_ceil-Z_pcb_top-pad2_gap 5.75 ok [secG, table] FK-H-02 1/1 seat width (each side) 2.121 wall*sqrt2 2.121 ok [secK] FK-H-02 1/1 pocket depth (seat to plate) 1.9 Z_ceil-Z_lid 1.9 ok [secK] FK-H-02 1/1 diagonal wall 1.5 wall 1.5 ok [secK, table] FK-H-02 1/1 lid seat Z 14.6 Z_lid 14.6 ok [table] FK-H-02 1/1 lid height 3.4 H-Z_lid 3.4 ok [table, notes] FK-H-02 1/1 lid front edge X 4.2 lid_x0 4.2 ok [table] FK-H-02 1/1 lid end X 99.2 L 99.2 ok [table] FK-H-02 1/1 tail facet 2 tail_facet 2 ok [table] FK-H-02 1/1 screw hole diameter 1.8 m16_clear 1.8 ok [table] FK-H-02 1/1 countersink diameter 3.3 m16_csk 3.3 ok [table] FK-H-02 1/1 countersink depth 0.75 (m16_csk-m16_clear)/2 0.75 ok [table] FK-H-02 1/1 front screw X 10.14 screw_x_front 10.14 ok [table] FK-H-02 1/1 rear screw X 95.95 X_screw_back 95.95 ok [table, notes] FK-H-02 1/1 screw Y 4.5 screw_dy 4.5 ok [table] FK-H-02 1/1 RF opening corner radius 1.5 rfw_r 1.5 ok [table] FK-H-02 1/1 RF opening start X 34.55 rfw_box[0] 34.55 ok [table] FK-H-02 1/1 RF opening end X 41.45 rfw_box[1] 41.45 ok [table] FK-H-02 1/1 RF pocket width 12.4 rfw_y+2*rfw_flange 12.4 ok [table] FK-H-02 1/1 RF pocket corner radius 2.3 rfw_r+rfw_flange 2.3 ok [table] FK-H-02 1/1 RF pocket depth 0.6 rfw_flange_t 0.6 ok [table] FK-H-02 1/1 lid plate underside Z 16.5 Z_ceil 16.5 ok [table] FK-H-02 1/1 RF pocket ceiling Z 17.1 Z_ceil+rfw_flange_t 17.1 ok [table] FK-H-02 1/1 RF pocket margin 0.8 rfw_flange 0.8 ok [table] FK-H-02 1/1 lid above the pocket 0.9 lid_t-rfw_flange_t 0.9 ok [table] FK-H-02 1/1 lanyard slot width 3.6 lan_slot_w 3.6 ok [table] FK-H-02 1/1 lanyard slot centre X 95.95 X_lan 95.95 ok [table] FK-H-02 1/1 lanyard slot chamfer 0.25 lan_chamfer 0.25 ok [table] FK-H-02 1/1 pocket start X 11.45 L_head 11.45 ok [table] FK-H-02 1/1 pocket end X 93.35 X_batt1 93.35 ok [table] FK-H-02 1/1 pocket plan corner radius 2 inner_r 2 ok [table] FK-H-02 1/1 lid plate thickness 1.5 lid_t 1.5 ok [table, notes] FK-H-02 1/1 seat width (each side) 2.121 wall*sqrt2 2.121 ok [table] FK-H-02 1/1 pocket half width at the seat 7.879 W/2-wall*sqrt2 7.879 ok [table] FK-H-02 1/1 panel depth 0.3 pan_depth 0.3 ok [table] FK-H-02 1/1 panel half width 5.4 W/2-C_edge-rail 5.4 ok [table] FK-H-02 1/1 boss start X 24.85 boss_box[0] 24.85 ok [table] FK-H-02 1/1 boss end X 33.65 boss_box[1] 33.65 ok [table] FK-H-02 1/1 boss start Y -7.6 boss_box[2] -7.6 ok [table] FK-H-02 1/1 boss end Y 4.8 boss_box[3] 4.8 ok [table] FK-H-02 1/1 boss corner radius 1 boss_r 1 ok [table] FK-H-02 1/1 boss height 2.95 Z_ceil-can_top_z-pad_gap 2.95 ok [table] FK-H-02 1/1 can boss face Z 13.55 can_top_z+pad_gap 13.55 ok [table] FK-H-02 1/1 front boss start X 18.4 boss2_box[0] 18.4 ok [table] FK-H-02 1/1 front boss end X 22.1 boss2_box[1] 22.1 ok [table] FK-H-02 1/1 front boss start Y 0.25 boss2_box[2] 0.25 ok [table] FK-H-02 1/1 front boss end Y 3.25 boss2_box[3] 3.25 ok [table] FK-H-02 1/1 front boss corner radius 0.5 boss2_r 0.5 ok [table] FK-H-02 1/1 front boss face Z 10.75 Z_pcb_top+pad2_gap 10.75 ok [table] FK-H-02 1/1 can pad free thickness 1.5 pad_t0 1.5 ok [table] FK-H-02 1/1 can pad gap 1.15 pad_gap 1.15 ok [table] FK-H-02 1/1 front pad free thickness 1 pad2_t0 1 ok [table] FK-H-02 1/1 front pad length 3.7 boss2_box[1]-boss2_box[0] 3.7 ok [table] FK-H-02 1/1 front pad width 3 boss2_box[3]-boss2_box[2] 3 ok [table] FK-H-02 1/1 front pad gap 0.75 pad2_gap 0.75 ok [table] FK-H-02 1/1 insert clearance 0.03 rfw_clear 0.03 ok [table] FK-H-02 1/1 lid screw length 6 lid_screw_len 6 ok [notes] FK-H-02 1/1 countersink edge to the facet edge 0.45 (W/2-C_edge)-(screw_dy+m16_csk/2) 0.45 ok [notes] FK-H-02 1/1 sliver csk - slot chamfer 0.3 screw_dy-m16_csk/2-(lan_slot_len/2+lan_chamf 0.3 ok [notes] == FK-H-03 1/1 sheet what shown P expression P value ok --------------------------------------------------------------------------------------------------------------------------------- FK-H-03 1/1 key width X 6.8 main_key[0] 6.8 ok [secX, top, table] FK-H-03 1/1 flange X 7.6 main_key[0]+2*flange_main 7.6 ok [secX, table] FK-H-03 1/1 pocket X 4.4 sw_body[0]+2*pocket_clear 4.4 ok [secX, table] FK-H-03 1/1 nub diameter 1.6 nub_d 1.6 ok [secX, table] FK-H-03 1/1 key height 2.75 main_top_z-main_face_z 2.75 ok [secX, notes] FK-H-03 1/1 face to flange underside 1.35 Z_seat-main_face_z 1.35 ok [secX] FK-H-03 1/1 flange thickness 0.45 flange_t 0.45 ok [secX, table] FK-H-03 1/1 flange underside to nub top 0.7 main_nub_z-Z_seat 0.7 ok [secX, notes] FK-H-03 1/1 pocket depth 1.2 main_top_z-(main_nub_z-nub_h) 1.2 ok [secX, table] FK-H-03 1/1 key width Y 6.8 main_key[1] 6.8 ok [secY, table] FK-H-03 1/1 pocket Y 3.4 sw_body[1]+2*pocket_clear 3.4 ok [secY, table] FK-H-03 1/1 ring LED axes (light input) 4.8 2*led_y 4.8 ok [secY] FK-H-03 1/1 flange Y 7.6 main_key[1]+2*flange_main 7.6 ok [top, table] FK-H-03 1/1 pocket corner radius 0.5 0.5 (build_key_main) 0.5 ok [top] FK-H-03 1/1 ring outer dia 4.9 ring_icon[0]+ring_icon[1] 4.9 ok [bot] FK-H-03 1/1 ring inner dia 3.9 ring_icon[0]-ring_icon[1] 3.9 ok [bot] FK-H-03 1/1 ring depth 0.03 ring_icon[2] 0.03 ok [bot] FK-H-03 1/1 key corner radius 1 main_key[2] 1 ok [bot, table] FK-H-03 1/1 ring mean dia 4.4 ring_icon[0] 4.4 ok [table] FK-H-03 1/1 ring width 0.5 ring_icon[1] 0.5 ok [table] FK-H-03 1/1 face edge chamfer 0.15 0.15 (build_key_main) 0.15 ok [table] FK-H-03 1/1 floor opening X 7 main_key[0]+2*key_clear 7 ok [table] FK-H-03 1/1 floor opening Y 7 main_key[1]+2*key_clear 7 ok [table] FK-H-03 1/1 nub height 0.5 nub_h 0.5 ok [table] FK-H-03 1/1 ring LED offset 2.4 led_y 2.4 ok [table] FK-H-03 1/1 LED gap at rest 0.6 led_gap_rest 0.6 ok [table] FK-H-03 1/1 main key X 25.65 X_main 25.65 ok [notes] FK-H-03 1/1 main key free play 0.15 pre_main 0.15 ok [notes] FK-H-03 1/1 LED gap at full travel 0.2 led_gap_rest-pre_main-sw_travel 0.2 ok [notes] == FK-H-04 1/1 sheet what shown P expression P value ok --------------------------------------------------------------------------------------------------------------------------------- FK-H-04 1/1 key length 10 side_key[1] 10 ok [secL, bot, table] FK-H-04 1/1 flange length 11 side_key[1]+2*flange_side 11 ok [secL, table] FK-H-04 1/1 face to flange underside 1.2 Z_seat-side_face_z 1.2 ok [secL] FK-H-04 1/1 recess depth 0.47 Z_seat+flange_t-(stiff_z0-plate_glue) 0.47 ok [secL, table] FK-H-04 1/1 flange thickness 0.45 flange_t 0.45 ok [secL, table] FK-H-04 1/1 flange underside to doubler top 0.6 side_nub_z-Z_seat 0.6 ok [secL, notes] FK-H-04 1/1 key width 4.2 side_key[0] 4.2 ok [secS, bot, table] FK-H-04 1/1 flange width 5.2 side_key[0]+2*flange_side 5.2 ok [secS, table] FK-H-04 1/1 recess width 3.8 plate_recess[0] 3.8 ok [secS, top, table] FK-H-04 1/1 chevron height 0.2 chevron_h 0.2 ok [secS, bot] FK-H-04 1/1 chevron apex angle 90 2*atan(chevron[2]/(2*chevron[1])) 90 ok [bot] FK-H-04 1/1 chevron stroke 0.6 chevron[0] 0.6 ok [bot] FK-H-04 1/1 chevron overall X 1.8 2*chevron[1]+chevron[0] 1.8 ok [bot] FK-H-04 1/1 chevron overall Y 3 2*chevron[2]+chevron[0] 3 ok [bot] FK-H-04 1/1 recess length 9.6 plate_recess[1] 9.6 ok [top, table] FK-H-04 1/1 recess corner radius 1 plate_recess[2] 1 ok [top, table] FK-H-04 1/1 plate length 9.4 stiffener[1] 9.4 ok [plate, table] FK-H-04 1/1 plate width 3.6 stiffener[0] 3.6 ok [plate, table] FK-H-04 1/1 doubler size 2 doubler[0] 2 ok [plate, table] FK-H-04 1/1 plate corner clip 0.8 stiffener[3] 0.8 ok [plate, table] FK-H-04 1/1 plate thickness 0.3 stiffener[2] 0.3 ok [plate, table] FK-H-04 1/1 doubler size 2 doubler[1] 2 ok [table] FK-H-04 1/1 key corner radius 1.5 side_key[2] 1.5 ok [table] FK-H-04 1/1 face edge radius 0.2 0.2 (build_key_side) 0.2 ok [table] FK-H-04 1/1 next key X 18.65 X_next 18.65 ok [notes] FK-H-04 1/1 end press distance 2 2.0 (side_key_end_press) 2 ok [notes] FK-H-04 1/1 end press force 1.035 side_key_end_press 1.035 ok [notes] FK-H-04 1/1 end press travel 0.73 side_key_end_press, rounded to 2 dec 0.73 ok [notes] FK-H-04 1/1 end press travel rubber only 3.9 side_key_end_press, rounded to 1 dec 3.9 ok [notes] FK-H-04 1/1 side key free play 0.25 pre_side 0.25 ok [notes] FK-H-04 1/1 glue film 0.02 plate_glue 0.02 ok [notes] == FK-H-05 1/1 sheet what shown P expression P value ok --------------------------------------------------------------------------------------------------------------------------------- FK-H-05 1/1 insert plug length 6.84 rfw_box[1]-rfw_box[0]-2*rfw_clear 6.84 ok [ins_top, table] FK-H-05 1/1 insert plug width 10.74 rfw_y-2*rfw_clear 10.74 ok [ins_top, table] FK-H-05 1/1 insert flange length 8.3 rfw_box[1]-rfw_box[0]+2*(rfw_flange-rfw_flan 8.3 ok [ins_top, table] FK-H-05 1/1 insert flange width 12.2 rfw_y+2*(rfw_flange-rfw_flange_clear) 12.2 ok [ins_top, table] FK-H-05 1/1 insert height 1.4 H-pan_depth-(Z_ceil-rfw_flange_drop) 1.4 ok [ins_sec] FK-H-05 1/1 insert flange thickness 0.8 rfw_flange_t+rfw_flange_drop 0.8 ok [ins_sec, table] FK-H-05 1/1 antenna spacer length 6 X_batt0-0.05-(X_pcb1+0.15) 6 ok [asp_top] FK-H-05 1/1 antenna spacer width 16.8 2*(inner_half-0.1) 16.8 ok [asp_top] FK-H-05 1/1 antenna spacer height 15.85 Z_ceil-rfw_flange_drop-0.15-pan_depth 15.85 ok [asp_side, asp_front] FK-H-05 1/1 plug face Z 0.3 pan_depth 0.3 ok [asp_side] FK-H-05 1/1 cell-wire rebate width 3.8 inner_half-0.1+cell_wire_channel[1] 3.8 ok [asp_front] FK-H-05 1/1 rebate floor Z 5.6 kb_z1+0.4 5.6 ok [asp_front] FK-H-05 1/1 sleeve outer dia 6 sleeve_od 6 ok [slv, table] FK-H-05 1/1 sleeve inner dia 4.6 sleeve_id 4.6 ok [slv, table] FK-H-05 1/1 sleeve length 10 sleeve_len 10 ok [slv_side, table] FK-H-05 1/1 insert plug radius 1.47 rfw_r-rfw_clear 1.47 ok [table] FK-H-05 1/1 insert clearance 0.03 rfw_clear 0.03 ok [table] FK-H-05 1/1 insert face below the lid top 0.3 pan_depth 0.3 ok [table] FK-H-05 1/1 insert flange clearance 0.1 rfw_flange_clear 0.1 ok [table] FK-H-05 1/1 floor plug length 5.04 frw_box[1]-frw_box[0]-2*rfw_clear 5.04 ok [table] FK-H-05 1/1 floor plug width 10.74 2*(frw_box[2]-rfw_clear) 10.74 ok [table] FK-H-05 1/1 sleeve slit 0.8 sleeve_slit 0.8 ok [table] FK-H-05 1/1 laser module diameter 6 las_d 6 ok [table] FK-H-05 1/1 texture depth 0.2 tex_depth 0.2 ok [table] FK-H-05 1/1 texture pitch 0.9 tex_pitch 0.9 ok [table] == FK-H-06 1/1 sheet what shown P expression P value ok --------------------------------------------------------------------------------------------------------------------------------- FK-H-06 1/1 kit length X 52.8 build_pmma_kit: (n+1)*kit_wall+n*cell 52.8 ok [top] FK-H-06 1/1 kit width Y 22 build_pmma_kit: max(cell+2*kit_wall, kit_min 22 ok [top] FK-H-06 1/1 tab width 0.6 kit_tab[0] 0.6 ok [top, det, table] FK-H-06 1/1 tab length 3 kit_gap 3 ok [top, table] FK-H-06 1/1 kit height Z 8.5 kit_h_pmma 8.5 ok [secA, det, table] FK-H-06 1/1 tab plane Z (bottom) 3.825 build_pmma_kit: (h-key)/2+flange from the fa 3.825 ok [det] FK-H-06 1/1 tab height (flange thickness) 0.45 flange_t 0.45 ok [det, table] FK-H-06 1/1 gap key flange - frame 3 kit_gap 3 ok [det] FK-H-06 1/1 kit length X 52.8 build_pmma_kit 52.8 ok [table] FK-H-06 1/1 kit width Y 22 build_pmma_kit 22 ok [table] == FK-H-07 1/1 sheet what shown P expression P value ok --------------------------------------------------------------------------------------------------------------------------------- FK-H-07 1/1 kit length X 45.4 build_pom_kit: 3*kit_wall+4*insert cell 45.4 ok [top] FK-H-07 1/1 kit width Y 39.3 build_pom_kit: 3*kit_wall+rows 39.3 ok [top] FK-H-07 1/1 tab width 0.6 kit_tab[0] 0.6 ok [top, table] FK-H-07 1/1 tab height 0.6 kit_tab[1] 0.6 ok [top, table] FK-H-07 1/1 tab length 3 kit_gap 3 ok [top] FK-H-07 1/1 tab length at the antenna spacer 5 kit_gap_tall 5 ok [top] FK-H-07 1/1 kit height Z 17 kit_h_pom 17 ok [secB, secC, table] FK-H-07 1/1 tab plane Z (bottom) 12.5 build_pom_kit: spacer side face middle 12.5 ok [secB] FK-H-07 1/1 tab plane Z (bottom) 12.5 build_pom_kit 12.5 ok [table] FK-H-07 1/1 tab plane Z (top) 13.1 build_pom_kit 13.1 ok [table] FK-H-07 1/1 kit length X 45.4 build_pom_kit 45.4 ok [table] FK-H-07 1/1 kit width Y 39.3 build_pom_kit 39.3 ok [table] == FK-H-08 1/1 sheet what shown P expression P value ok --------------------------------------------------------------------------------------------------------------------------------- FK-H-08 1/1 mould length 48 mould_size[0] 48 ok [cav, lid, table, notes] FK-H-08 1/1 mould width 28 mould_size[1] 28 ok [cav, table, notes] FK-H-08 1/1 cavity pitch 9.2 mould_pitch 9.2 ok [cav] FK-H-08 1/1 plateau width 3.8 plate_recess[0] 3.8 ok [lid] FK-H-08 1/1 plateau length 9.6 plate_recess[1] 9.6 ok [lid] FK-H-08 1/1 plateau corner radius 1 plate_recess[2] 1 ok [lid] FK-H-08 1/1 plateau height 0.47 Z_seat+flange_t-(stiff_z0-plate_glue) 0.47 ok [lid] FK-H-08 1/1 flange depth 0.45 flange_t 0.45 ok [secA] FK-H-08 1/1 cavity depth (key face) 1.65 Z_seat+flange_t-side_face_z 1.65 ok [secA] FK-H-08 1/1 vent width 1 mould_vent[0] 1 ok [secA] FK-H-08 1/1 vent depth 0.1 mould_vent[1] 0.1 ok [secA] FK-H-08 1/1 vent hole 1 mould_vent_hole[0] 1 ok [secA, table] FK-H-08 1/1 vent counterbore 2.5 mould_vent_hole[1] 2.5 ok [secA, table] FK-H-08 1/1 runner width 1.2 mould_runner[0] 1.2 ok [secA, table] FK-H-08 1/1 runner depth 0.45 mould_runner[1] 0.45 ok [secA] FK-H-08 1/1 sprue diameter 2.5 mould_sprue_d 2.5 ok [secA, table] FK-H-08 1/1 cap width at the flange step 4.12 side_key[0]+2*mould_cap_offset 4.12 ok [secB, table] FK-H-08 1/1 flange width at the flange step 5.2 side_key[0]+2*flange_side 5.2 ok [secB] FK-H-08 1/1 chevron groove depth 0.2 chevron_h 0.2 ok [secB] FK-H-08 1/1 mould draft 1 mould_draft 1 ok [secB, table] FK-H-08 1/1 floor radius 0.2 0.2 (build_key_side) 0.2 ok [secB, table] FK-H-08 1/1 chevron groove width 0.6 chevron[0] 0.6 ok [secB] FK-H-08 1/1 chevron cutter 0.6 chevron[0] 0.6 ok [secB, table] FK-H-08 1/1 resin back pocket depth (cavity half) 2.15 resin_t[0]-cavity depth-resin_floor 2.15 ok [rcav] FK-H-08 1/1 resin rim 3 resin_rim 3 ok [rcav] FK-H-08 1/1 resin rib 2 resin_rib 2 ok [rcav] FK-H-08 1/1 resin bolt hole 3.4 resin_bolt[0] 3.4 ok [rlid] FK-H-08 1/1 resin bolt length 16 resin_bolt[1] 16 ok [rlid, table] FK-H-08 1/1 resin cavity half thickness 6 resin_t[0] 6 ok [rsec, table] FK-H-08 1/1 resin lid thickness 5 resin_t[1] 5 ok [rsec, table] FK-H-08 1/1 plate thickness 8 mould_t[0] 8 ok [table, notes] FK-H-08 1/1 parting face flatness 0.02 0.02 (drawing) 0.02 ok [table] FK-H-08 1/1 cap length at the flange step 9.92 side_key[1]+2*mould_cap_offset 9.92 ok [table] FK-H-08 1/1 chevron groove radius 0.3 chevron[0]/2 0.3 ok [table] FK-H-08 1/1 corner radius limit (tool) 0.6 mould_runner[0]/2 0.6 ok [table] FK-H-08 1/1 dowel diameter 2 mould_dowel[0] 2 ok [table] FK-H-08 1/1 dowel press depth 5 mould_dowel[2] 5 ok [table] FK-H-08 1/1 M3 thread depth 6 mould_m3[2] 6 ok [table] FK-H-08 1/1 M3 tap drill 2.5 mould_m3[0] 2.5 ok [table] FK-H-08 1/1 M3 drill depth 7 mould_m3[1] 7 ok [table] FK-H-08 1/1 M3 clearance 3.4 mould_m3[3] 3.4 ok [table] FK-H-08 1/1 dowel length 8 mould_dowel[1] 8 ok [table] FK-H-08 1/1 resin pin diameter 4 resin_pin[0] 4 ok [table] FK-H-08 1/1 resin socket diameter 4.2 resin_pin[3] 4.2 ok [table] FK-H-08 1/1 dowel height above the parting face 3 mould_dowel[1]-mould_dowel[2] 3 ok [notes] numbers vs P: 441 distinct entries, 0 mismatches Cross-check against the STEP solids (ray probes): value of P / drawing against the solid what P/drawing solid diff ------------------------------------------------------------------------------------------------------------------- PMMA kit length X 52.8 52.8 0 ok PMMA kit width Y 22 22 0 ok PMMA kit height Z 8.5 8.5 0 ok PMMA kit tab bottom Z 3.825 3.825 0 ok PMMA kit tab top Z 4.275 4.275 0 ok PMMA kit gap frame - flange (first) 3 3 0 ok POM kit length X 45.4 45.4 0 ok POM kit width Y 39.3 39.3 0 ok POM kit height Z 17 17 0 ok POM kit tab bottom Z (insert) 12.5 12.5 0 ok POM kit tab top Z (insert) 13.1 13.1 0 ok mould cavity half length X 48 48 0 ok mould cavity half width Y 28 28 0 ok mould cavity depth at the key face 1.65 1.65 0 ok mould chevron groove floor depth 1.85 1.85 0 ok mould plateau height 0.47 0.47 0 ok mould cap width at the flange step (first cavity) 4.12 4.12 0 ok mould flange pocket length at its floor (first cavity) 11 10.995 -0.005 ok resin mould cavity depth at the key face 1.65 1.65 0 ok resin mould chevron groove floor depth 1.85 1.85 0 ok resin cavity half thickness 6 6 0 ok resin lid thickness 5 5 0 ok resin mould plateau height 0.47 0.47 0 ok tray length 99.2 99.2 0 ok tray width 20 20 0 ok tray height (head block) 18 18 0 ok optic bore diameter 10.1 10.1 0 ok optic bore axis Y -3.825 -3.825 0 ok optic bore floor X (depth D_w) 8.83 8.83 0 ok solid head block behind the optic bore floor 2.62 2.62 0 ok LED wire hole upper: Y centre (X 10) -0.975 -0.975 0 ok LED wire hole upper: diameter (X 10) 1.5 1.5 0 ok LED wire hole lower: Y centre (X 10) -6.675 -6.675 0 ok LED wire hole lower: diameter (X 10) 1.5 1.5 0 ok LED wire groove (upper): start X 6.13 6.13 0 ok front lid tap X 10.14 10.14 0 ok laser bore diameter (Z span) 6.1 6.1 0 ok laser axis Z 5.9 5.9 0 ok laser axis Y 5.85 5.85 0 ok laser set-screw hole X 5.5 5.5 0 ok laser set-screw tap drill (X span) 1.25 1.25 0 ok laser set-screw hole Y 4.8 4.8 0 ok no hole in the bottom face under the laser (solid to the bore) 2.85 2.85 0 ok PCB ledge height Z_pcb_bot 9.2 9.2 0 ok trough width between the ledges 15.4 15.4 0 ok floor thickness (band between the bottom panels, X 64.70) 1.5 1.5 0 ok side wall top at the lid seat (Z_lid) 14.6 14.6 0 ok main key opening X 7 7 0 ok main key opening centre X 25.65 25.65 0 ok next key opening X 4.4 4.4 0 ok previous key opening Y 10.3 10.3 0 ok bezel floor Z (beside the next key) 0.5 0.5 0 ok KB boss top Z at the boss edge (25.65, +5.8) 4.4 4.4 0 ok KB tap drill diameter (25.65, +5.8) 1.25 1.25 0 ok KB boss top Z at the boss edge (25.65, -5.8) 4.4 4.4 0 ok KB tap drill diameter (25.65, -5.8) 1.25 1.25 0 ok KB rib top Z (18.65, +Y) 4.4 4.4 0 ok KB rib top Z (18.65, -Y) 4.4 4.4 0 ok KB rib top Z (32.65, +Y) 4.4 4.4 0 ok KB rib top Z (32.65, -Y) 4.4 4.4 0 ok floor RF window length 5.1 5.1 0 ok floor RF window width 10.8 10.8 0 ok lid thickness (bay, no panels) 1.5 1.5 0 ok lid seat width (X 50, +Y side) 2.121 2.121 0 ok can boss face Z 13.55 13.55 0 ok front boss face Z 10.75 10.75 0 ok main key height (outer face to top face) 2.75 2.75 0 ok main key nub top Z 2.2 2.2 0 ok main key width X 6.8 6.8 0 ok main key flange X 7.6 7.6 0 ok side key doubler top Z (presses the switch) 2.1 2.1 0 ok side key length Y 10 10 0 ok side key flange Y 11 11 0 ok side key plate top Z (beside the doubler) 1.8 1.8 0 ok solid probes: 74, mismatches 0, known differences from P 0